Flintlock Rifle Kits, how to build a diy flintlock rifle

I grew up watching Fess Parker play Davy Crockett and Daniel Boone on television. Those programs started my life-long interest in frontier history, and they also made me want to be out in the woods with a flintlock long rifle in the worst way. But I had some growing up to do first. My father was an avid hunter, but he had no interest in those old-fashioned front-stuffers. When it came to guns, my dad was modern all the way.

My Own Flintlock Rifle

I couldn’t complain, though. My dad outfitted me with modern rifles and shotguns, and I hunted beside him with those guns from the time I was 12 years old. But my desire to emulate the exploits of Boone and Crockett never went away. So I saved my money and, at the ripe old age of 18, I drove my beat up Chevy Malibu to the headquarters of Connecticut Valley Arms (CVA), which, at the time, was located in Old Saybrook, Conn. I plunked $78 on the counter and walked out with one of the CVA Kentucky flinklock rifle kits. From that day forward, I’ve never been without at least one flintlock long rifle in the gun rack.

I used that CVA Kentucky throughout my college years. It was a solid rifle that was blessed with an accurate barrel. I won my share of muzzleloading matches with it. Unfortunately, in terms of aesthetics, not to mention historical accuracy, my CVA had about as much in common with the sleek Berks County rifle that Fess Parker carried in his Davy Crockett role as Spam has with a perfectly grilled ribeye.

Early Inspiration

Back in the 1970s there were only a couple commercially available long rifles that were even remotely historically correct, and they were priced out of my reach. So, in 1978, I picked up the Dixie Gun Works catalog and ordered its least expensive, pre-carved stock along with a cheap flintlock, a Douglas .45-caliber barrel and the various small parts needed to build a flintlock long rifle.

By then I had moved to the city of Philadelphia to start my career, and I built that first rifle in a one-bedroom apartment. I didn’t have a workbench…I didn’t even have a vice. Luckily, I was young and I had a strong grip. For tools I had a power drill, an X-Acto knife with an assortment of knife and chisel blades, and a small collection of rasps and files.

flintlock rifle kits, flintlock long rifle, stock
Completing a long rifle build takes patience. The author put approximately 300 hours of work into this rifle.

Surprisingly, given my lack of both tools and experience, that first build turned out quite nice. Don’t get me wrong, it would not have won a ribbon at Dixon’s Rifle Makers Fair, but it shot well and it certainly looked more legit than anything I could’ve bought off the shelf.

That was 36 years ago, but things really haven’t changed. If you are interested in 18th century military muskets, there are a number of very good, period-correct production models available to choose from. But if your interests run to the long rifles that would have been carried by frontiersmen during the 18th century, there are only a couple of production models available. And to be honest, even they leave a lot to be desired. So, just as in 1978, if you want an authentic flintlock long rifle, your best option is to build your own.

Today’s Builds

Luckily, today’s rifle builders have it easier than I did back in the dark days of the 20th century. Today there are far more suppliers of quality parts than there were then, and, thanks to the internet, those suppliers are easier to find than ever before. There is also more good information available than there was in the past.

When I built my first rifle, I used a 25-cent instruction sheet from Dixie Gun Works. Believe me, I got my quarter’s worth, but there was still an awful lot left uncovered. Today there are several excellent how-to books, and there are a number of really excellent rifle maker’s forums on the internet that you can turn to for advice. Many of the best professional rifle builders in the country frequent these boards and they are generous with their knowledge.

I recently finished my first long rifle build after a 23-year layoff, and I made full use of all the new resources that are available. In the course of doing this build, I think I learned more than I did during the dozen or so rifle builds I did between 1978 and 1990. If you’re thinking of building your own long rifle, some of what I learned may help smooth the road for you.

Pre-Build Planning

There are a few areas you should address before you start your build. First, you need a good idea of what you want your rifle to look like. There are lots of different styles of long rifles. Just about every county in Pennsylvania had its own unique style of rifle building, and there were rifle makers in Virginia, the Carolinas and, eventually, in points west like Tennessee.

flintlock rifle kits, flintlock long rifle, custom
Building your own rifle allows you to add authentic touches like patchboxes that most production rifles can’t provide.

George Shumway’s two-volume set, Rifles of Colonial America, is the bible for familiarizing yourself with long rifle design. It shows a number of “schools” of rifle building, with detailed photographs of several rifles from each school. Unfortunately, this book is out of print. Used versions are easy to find on websites like Amazon.com, but buying one can be pretty pricey. As an alternative, the Kentucky Rifle Foundation sells a series of DVDs featuring a dozen or so rifles on each disc. Each rifle will have a number of high-resolution, full-color images. These DVDs are reasonably priced, and they are an outstanding resource.

Next you should pick up a good book on building long rifles. In my opinion, the two best are The Art of Building the Pennsylvania Long rifle by Dixon, Ehrig and Miller and The Gunsmith of Grenville County: Building the American Long rifle by Peter A. Alexander. I’d recommend that you get both books. They aren’t very expensive and they complement each other very well. Read them cover to cover before you start, and refer to them often during the build.

Tools It Takes

The last pre-build area to address is tools. If you love your first build so much that it evolves into a continuing hobby, you’ll find yourself picking up a lot of tools over time, but for your first build a limited tool kit will get the job done. The good news is that you probably already have a lot of what you need in your shop right now. You’ll need a drill—whether it is hand cranked or powered by electricity really doesn’t matter. You’ll also need a hacksaw and a coping saw. If you have a band saw, and the skill to use it, you can dispense with the coping saw.

You will need a set of files for metalworking and rasps for woodworking. As time goes on, you may want to get specialized gunsmithing files and cabinetmakers’ rasps, but I find that hardware store files and rasps work just fine. Personally, I have an entire large toolbox that is filled with files and rasps. I’ll admit it, I’m a raspaholic. But during the build that I just finished, I basically used only three files and three rasps. But I do recommend that you get a good set of needle files and a good set of rifflers. You might not use them often, but when you need one, nothing else will do.

Chisel & Stone

The most important tools that you’ll use during the build are your chisels. You don’t need many. One 3mm or 4mm chisel and a quarter-inch chisel will get you through most of the build. Chisels are one thing that you can’t scrimp on. Buy the best. I use Pfeil’s Swiss-made chisels. They take an edge you can shave with, and they hold it well.

flintlock rifle kits, flintlock long rifle, tools
With a few tools and a lot of patience, you can turn a collection of parts into an authentic flintlock long rifle that you will be proud to own.

I won’t lie to you, they are expensive at about $30 to $40 dollars each, but it is money well spent. Woodcraft Supply is an excellent source for these chisels. I also use a couple of American-made bent inletting chisels from Track of the Wolf. They let you get into a mortise to flatten out the bottom of the cut. And I still use that old X-Acto kit from my first build, though with new blades. I mostly use it to outline around parts, but I wouldn’t want to be without it.

If you don’t have a good, hard sharpening stone, you’ll want to get one. I sharpen my chisels about every 15 minutes while I’m using them, and between sharpenings I’ll strop a chisel by making a couple of passes over a leather strap every few minutes. That’s how I maintain a razor’s edge, which you need to make clean cuts in hard maple.

Power Tools?

When you are building a rifle, power tools just let you make mistakes faster. As a rule of thumb, if you can do it with a hand tool, you should. Leave the Dremel in the drawer. But there are a couple of worthwhile exceptions.

Personally, I can use a power drill more accurately than I can use a hand drill. I am also a big fan of using a drill press. You can certainly build a rifle without one. I know this because I built a dozen rifles in the 1970s and ’80s without using one. However, there are at least 10 times during the course of the build where you will need to do precise drilling. A drill press can save your bacon.

Custom Flintlock Rifle Kits

After you’ve settled on the style of rifle you want to build, and with your books and tools accounted for, all that remains is to get the gun parts and start building. As a first-time builder, you have a lot of choices to make. You can determine exactly how challenging you want your first build to be.

‘In the White’

At the easiest end of the spectrum are “in the white” guns. These are guns that have been completely inletted and assembled, but all the finishing remains to be done by you. So the stock needs to be sanded, stained and finished, and the metal parts require polishing and bluing or browning. This can be a good option if you are new to long rifles. All the hard stuff is done for you, but you can still exercise your creativity by adding detail work like moldings and carving or inlays and patchboxes.

Wolf's Bucks County kits
The author built this rifle from Track of the Wolf’s Bucks County rifle kit.

Semi-custom builders like Tennessee Valley Muzzleloading (TVM) offer “in the white” versions for one hundred dollars less than its completed rifles. Ordering an “in the white” rifle and installing your own brass patchbox and a hunter’s star on the cheekpiece, along with detail moldings on the lower buttstock and ramrod channel, will save you about $300 over the cost of a finished TVM rifle with those options.

Pre-Inlet Flintlock Rifle Kits

Next up on the difficulty scale are the pre-inlet kits. These are offered by many companies. Track of the Wolf, Tennessee Valley Muzzleloading and Jim Chambers all offer this type of kit. The pre-inletted kits are probably the most popular choice for first-time builders.

You will get a pre-carved stock that has been profiled to the shape of the type of rifle you are building. The stock will have the barrel channel cut and the ramrod hole drilled into the stock. The lock and trigger mortises will be in place, but left undersized. The kit will include the lock, barrel and all the miscellaneous parts needed to build your rifle. Building one of these kits is a major undertaking, but they can produce a fine, handcrafted rifle.

Assemble Your Own

Rather than buying a kit, you can assemble your components individually—this means you get an un-inletted, pre-carved stock with a profiled buttstock and the barrel and ramrod channels cut, but no pre-inlets for locks or triggers. This is my preferred way to go. It gives you the flexibility to select exactly the components you want to use on your rifle.

At the most difficult end of the spectrum, you can assemble your individual parts and, instead of buying a pre-carved stock, you can make your own from a maple plank. This adds a considerable degree of difficulty to the build, so make sure you are really up for it before you go that way.

Modern-Day Flintlock Rifle Replica

In the past, I only built rifles from individual components, but, for the rifle I just completed, I used a Bucks County rifle kit from Track of the Wolf. The kit came with a Colerain 42-inch-long, 0.81-inch-wide, .45-caliber barrel and an excellent Large Siler flintlock. I selected a stock in a plain grade of maple. It was profiled with a typical Bucks County buttstock style. The kit came with double set triggers, but I prefer a single trigger, so I filled the pre-cut trigger mortise in the stock with a piece of maple and I installed an R.E. Davis single trigger. I also ordered a Bucks County-style patchbox. These are very distinctive because they are hinged on the side of the box, rather than at the top as most patchboxes are.

Have a bag and horn set handy for each flintlock longrifle you own.
A smart play: The author recommends that you have a bag and horn set up for each muzzleloading rifle that you own.

This was my first flintlock rifle build in over 20 years, and it is by far the nicest rifle I’ve ever built. And it isn’t because I’ve become any more skillful over the last couple of decades. What I have become is more patient. So, my final advice to you is this.

When you start your build, don’t focus on completing the entire project. Instead, realize that the build is made up of maybe 100 individual projects. As you are doing each one of those projects, give it your full attention as if it was a whole build in and of itself. So, if you are filing and polishing the buttplate before inletting it, give that job all your focus. Work it carefully until you at 100-percent satisfied with it, then move to the next task. If you work that way, you’ll end up with a completed rifle that you can be proud of.

For More Information:

Up Next

20 PDWs For Ultimate Close-Quarters Personal Defense

Designed to offer a balance between portability and power, PDWs deliver when the chips...